The acquisition of a quality roller will cost a lot. But, having bought a good thing once, you can be sure that it will serve you for a long time. The main thing is to properly care for her. Timely cleaning will extend the life of your tool. How to quickly and efficiently wash the roller from the remaining paint?
- Cleaning the tool from water-based dyes
- How to wash with oil-based products
- We clean the tool from acrylic
- Roller tips
Cleaning the tool from water-based dyes
To clean the roller from water-based paints, prepare a special solution. To do this, you need a bucket, cleaning agent and fabric softener. Each tool needs a separate capacity:
- Pour water into a bucket (it should not be cold) and dissolve two glasses of fabric softener, shake everything thoroughly.
- When the product has completely dissolved, the surface tension of the water will change, and the paint will begin to get wet.
- You can not use a softener, but replace it with a simple dishwashing detergent mixed with warm water.
- Before you put the roller in the solution, try to remove the maximum amount of paint from it by turning and pressing it in the construction tray.
- The tray can be replaced with old newspapers. Arrange them in several rows and roll the tool on the floor, pressing it against the newspapers.
- Now we lower the roller in a container with water and detergent. Hold for about half a minute, then remove from the bucket and rinse thoroughly under running water, slightly warm. Wash off until the flowing water is clean.
- After we managed to get rid of the traces, we squeeze the tool sponge so that all the water comes out of it, then we wipe it with a bath towel or wrap it in a thick layer of paper towels. When all the excess moisture is absorbed, hang up to dry.
To extend the life of the instrument, it is best to store the instrument wrapped in film so that dust and dirt do not settle.
to contents ↑How to wash with oil-based products
The method of cleaning the tool sponge from oil paint differs significantly from the water-based cleaning. With this cleaning method, water cannot be used. Paint cannot dissolve in water - alcohol must be used.
First remove the maximum residue using newspapers. Spread old newspapers on the floor and roll a roller over them.
Pour alcohol into special dishes, put the tool there. Roll it in a container with a solvent until completely cleaned, and then hang to dry. When the roller is dry, it is advisable to cover it with a film or wrap it in foil to protect it from dirt and dust.
We clean the tool from acrylic
Cleaning the instrument after working with acrylic paint is quite simple. For such works, short-haired cylinders are used, and it is much easier to wash them off the tracks than fur ones.
Acrylic paints are most often used for repairs and for household needs. In their composition there are special substances that form the film. The best thing rinse off acrylic paintuntil she froze.If after the end of work no more than 24 hours have passed, then the cylinder can be washed under running warm water. You can place the instrument in warm water for about 20 minutes to get rid of traces.
After 24 hours, the paint has completely solidified, and it will be impossible to wash it without the use of additional funds. For this you need acetone, gasoline, white spirit.
Any solvent must be poured into the container and place the roller there for a while. After the paint layer has softened, remove it with any cloth or scraper. Rinse the roller well under water until it is clean.
You can use special cleaners for acrylic paints for cleaning. You can buy them at a building materials store. When using a remover or any other type of solvent, be sure to use gloves.
You can also resort to the help of a universal cleaner, which is also available in any construction department. It includes gasoline and alcohol. This tool can remove any kind of paint.
to contents ↑Roller tips
If you have stopped painting work for a while, you can put the roller in a plastic bag to prevent the paint from drying out. The tool can be stored in a bag by tying it tightly and placing it in the refrigerator. There the instrument can lie all night. Before use, remove it from the refrigerator in advance and allow it to lie down at room temperature.
What can be done if you didn’t have time to wash the roller in time and the paint has already thoroughly dried up? Throwing away an expensive tool is a pity. There is a very effective way to restore dried pile on the fiber slave cylinder.
There are no problems getting rid of water-based paint: even dried paint can be easily washed off with plain running water. But with nitro enamel or any other, made on the basis of a solvent, you have to tinker a bit.
You will need:
- solvent;
- unnecessary fabric;
- scraper;
- any capacity.
Try using a scraper to remove as much dry paint as possible from the surface of the cylinder. Then pour solvent into the prepared container and lower the tool there. When the sponge becomes soft, use a rag to remove traces and rinse the cylinder with water. The process is repeated until all traces are completely removed.
Then rinse the instrument in water with a cleaning agent and dry it. The dry roller is ready to work again - it can be used for painting with any shade.
